Tuesday, February 28, 2017

99 Blocks of Beauty on the Wall

...the design wall, that is. If you didn't get the "99 Bottles of Beer on the Wall" correlation, don't worry, it just means you're not as old as I am.  :)

On to the point. In this case, a wedge point.

Anyone who regularly watches Fons and Porter's For the Love of Quilting show has probably seen the quilt called "String Me Along," by Dodi Lee Poulsen. (Click on that link to get the pattern.) This lively, colorful quilt really got my attention.

From two yards of a black and white polka-dot fabric, you cut wedge-shaped pieces that fit exactly in one corner of a foundation square (muslin, lightweight permanent stabilizer, tear-away stabilizer, or paper) and extend just through the opposite corner. (I used a 7-1/2 inch square, which is larger than the pattern. I cut my own wedge template and barely got all my wedges out of the yardage; in fact I had to shorten four of them. That's what I get for trying to guess at the directions before I bought the pattern--which I've now done.)




Then you sew a strip of fabric down each side of the wedge piece with a 1/4 inch seam, making sure each strip extends past the edges of the foundation square before you sew it down. Finger-press each seam away from the polka-dot fabric.





Oops, obviously not the same block as in the first photo!


Keep adding strips to either side and finger-press the seams away from the center, until the square is completely covered.

TIP: If you are using paper for the foundation, which is what I did (it's a good way to recycle used printer paper) keep the paper on until the block is finished so you'll know how long your strips need to be, but don't sew through the paper after the first two seams. Just fold the paper back to sew the rest of the seams, unfolding it only to check the length of each additional strip.



You'll be glad you only sewed through it twice when it's time to tear the paper off--which is the next step.


After that, trim your block by lining up a square ruler with the polka-dot corner.

Now is the time to press your block, with a dry iron.

UPDATE (correction): Reverse those last two instructions. I pressed the un-trimmed block nice and flat, THEN trimmed it.



I used up all kinds of scraps on this project, ending up with ninety-nine 7-1/2 inch square blocks, for a quilt that will be 63 x 77 inches. That's not quite according to directions in the pattern, which ends up with 96 slightly smaller blocks. I would strongly suggest using the pattern. It would have saved me some guess work and yardage shortage.

This is as far as it's come, but I'm liking the look of it. It isn't the same block arrangement shown in the pattern, and I've seen two other arrangements, as well, on the internet somewhere. All are lovely.


Just a note: When joining the blocks and the rows, I did press the seams open instead of to one side, and it was the only time I used steam. Pressing, not ironing.

Another tip: For quick preparation of paper foundation squares, use the square ruler you'll be using to trim your blocks AND a rotary cutter set aside only for paper. (I keep a used, dull blade in that one, as it cuts paper just fine--two squares at a time!) That rotating cutting mat is super helpful, too.

Have a great week. Spring is starting early here in Kentucky, and we are loving it!

Linda

4 comments:

  1. I love the two shapes it makes. Great pattern.

    ReplyDelete
    Replies
    1. Thanks, Angie. I wish I could find those other arrangements I saw, but haven't been able to locate them again.

      Delete
  2. Whoa!!! That is so prettily striking!

    ReplyDelete
    Replies
    1. Lynnette, that's exactly what I thought when I saw the original on tv!

      Delete

Comment moderation has been enabled merely to prevent spam. Your comment should show up within a day or two. Thank you for your patience.